Pearl Elite Support

download the PDF on the Pearl PTM Solenoid replacement disassembly and cleaning

Download the PDF on the Pearl Elite Solenoid Replacement disassembly and cleaning

If you experience Possible Causes Solution Leaks Pretreatment solution dripping from Solenoid Hose may have come loose. Push hose in to quick connect Excessive pretreatment solution dripping from nozzle Nozzle Cap is loose Tighten Nozzle Cap Nozzle O-Ring is not installed Install Nozzle O-Ring Check Valve is not installed Install...

If desired operation is not within the range of factory default settings, platen height, viscosity setting, fan timing, and auto prime timing can be adjusted. 1. Adjusting Platen Height The Platen height can be adjusted to set the desired amount on the shirt. Raising the platen will bring the spray...

 The Pearl Elite is equipped with a cost calculator that allows users to determine the cost of pretreatment used on a single shirt or the cost for a run of shirts. 1.Entering Pretreatment Cost: Enter the Stats Menu by pressing the Stats Menu icon. Press the Cost/Gal # for either the Dark...

 The Pearl Elite has a save feature that allows users to save settings and modes. The save feature will allow up to twenty files to be stored in the memory of the machine. 1. To save the current settings, open the Save Menu by pressing the Save Menu icon. 2. The...

It is important to keep the Pearl Elite clean during extended use. The pretreatment solution can build up salt deposits that can inhibit normal operation of the Pearl Elite. It is recommended to clean the inside of the Pearl Elite after every use to prevent build up of pretreatment that...

The Pearl Elite stores setting and cycle information, as well as estimated pretreatment container levels during power off. It is important to follow these shut down procedures to allow this information to be stored correctly. The Pearl Elite will not allow the unit to properly power down with pretreatment solution...

When anticipating extended periods of non-use of the Pearl Elite, it is critical to follow these maintenance procedures. It is required to follow these steps daily after each use of the Pearl Elite. 1. To flush the Pearl Elite, enter the Maintenance Menu by pressing the Maintenance Menu icon. 2....

When changing pretreat it is important to follow these steps to ensure proper function the the Pearl Elite. The internal volume (mL) counters use these maintenance buttons to calculate the estimated usage. 1. To change the pretreat, enter the Maintenance Menu by pressing the Maintenance Menu icon. 2. Remove the...

The Spray Cycle is the process the Pearl PTM uses to lay a flat and even layer of pretreatment solution on to the garment. 1. To begin the Spray Cycle, enter the Home Menu by pressing the Home Menu Icon. 2. The Home Menu will display the current garment selection,...

Loading the garment properly will ensure even, consistent spray patterns. 1. Place the garment on the Platen as shown in the figure below with the collar of the garment towards the back of the machine. 2. Tuck the excess fabric under the platen. 3. Push the Drawer in all the...

 The settings will allow the user to control the spray density and spray length. 1. To adjust the settings, enter the Settings Menu by selecting the Settings Menu icon. 2. The Spray Density can be adjusted by pressing the Spray Density Setting and entering a value between(20 – 100). 3....

Priming the Pearl Elite is required for proper spray pattern on the garment. If the Pearl Elite is improperly primed, you may not get an even, flat and consistent spray pattern on the garment. 1. To prime the machine, enter the Maintenance Menu by selecting the Maintenance Menu icon. 2....

Home Menu 1. Start/Stop Button Press to start or stop spray cycle. 2. Light Pretreat Level Meter Displays estimated light pretreat remaining. 3. Dark Pretreat Level Meter Displays estimated dark pretreat remaining. 4. Garment selection Displays garment selection: light or dark garment. 5. Spray Length Area Displays spray length setting....

The Pearl Elite is powered with either 110V/60Hz or 220V/50z. Please check with distributor to verify the power requirements for the Pearl Elite in your region. 1. Plug the power cord in to the power connector located on the back of the Pearl Elite. 2. Press the Power Switch to the...